13:09:44 - Sat, Apr 20, 2024 -
10°C
10°C709390-0001 Parts List
TB25 Model - 709390-0001 |
||||||
|---|---|---|---|---|---|---|
| Figure | Part Number | Description | Quantity | |||
| 3 | 409589-0660 | Caracola admisión m. | 1 | |||
| 3 | Caracola admisión | 1 | ||||
| 35 | 400698-0001 | Tapón ( compressor housing ) | 1 | |||
| 2 | 400589-0375 | Retaining ring ( compressor housing ) | 1 | |||
| 4 | 403069-0164 | O ring ( compressor housing ) | 1 | |||
| - | 443854-0198 | C.H.R.A. | 1 | |||
| 8 | 444357-0013 | Bearing housing | 1 | |||
| 23 | 432236-0003 | Bearing | 2 | |||
| 24 | 444428-0001 | Retaining ring ( bearing ) | 3 | |||
| 12 | 435405-0001 | Turbine wheel | 1 | |||
| 13 | 435523-0001 | Heat shield | 1 | |||
| 11 | 400749-0006 | Piston ring ( turbine side ) | 1 | |||
| 19 | 443852-0002 | Thrust collar | 1 | |||
| 22 | 432254-0002 | Thrust bearing | 1 | |||
| 21 | 400810-0410 | Screw ( coj. empuje ) | 3 | |||
| 15 | 432280-0001 | Plate insercción | 1 | |||
| 20 | 403069-0163 | O ring ( plato insercción ) | 1 | |||
| 14 | 400589-0181 | Retaining ring ( plato insercción ) | 1 | |||
| 17 | 403818-0009 | Piston ring ( compressor side ) | 1 | |||
| 10 | 431350-0001 | Compressor wheel | 1 | |||
| 9 | 700192-0001 | Shaft nut | 1 | |||
| 7 | 430609-0332 | Turbine housing | 1 | |||
| 6 | 432726-0001 | Clamp ( turbine housing ) | 2 | |||
| 5 | 400788-0816 | Bolt ( turbine side ) | 4 | |||
| 31 | 430418-0036 | Actuator | 1 | |||
| 43 | 432012-0001 | Rod end ( actuator ) | 1 | |||
| 42 | 413853-0001 | Nut ( rod end actuator ) | 1 | |||
| 1 | 400724-0610 | Screw ( actuator ) | 2 | |||
| 28 | 400702-0025 | Retaining ring ( actuator ) | 1 | |||
| 100 | Gasket ( turbine inlet ) | 1 | ||||
| 105 | Gasket ( turbine outlet ) | 1 | ||||
| 115 | Gasket ( oil outlet ) | 1 | ||||
| 155 | 432546-0001 | Stud outlet | 5 | |||
| Pressure actuator Type = Pressure | Angles | |||||
| 0.389 - 0.419 bar = 0.38 mm | δ (delta) = 64º | |||||
| ε (epsilon) = 122.5º | ||||||
| Balance VSR | ||||||
| 1.5G between 0 - 80.000 rpm | ||||||
Updated on November 05, 2008